Step | Water dispenser hamilton beach service manual. Command | Purpose |
1 | Router# configure terminal | Enters global configuration mode. |
2 | Router(config)# service timestampstypedatetime [msec] [localtime] [show-timezone] | Instructs the system to timestamp syslog messages; the options for the type keyword are debug and log. |
3 | Router(config)#logginghost | Specifies the syslog server by IP address or host name; you can specify multiple servers. |
4 | Router(config)# logging traplevel | Specifies the kind of messages, by severity level, to be sent to the syslog server. The default is informational and lower. The possible values for level are as follows: Emergency: 0 Alert: 1 Critical: 2 Error: 3 Warning: 4 Notice: 5 Informational: 6 Debug: 7 Use the debug level with caution, because it can generate a large amount of syslog traffic in a busy network. |
5 | Router(config)# logging facilityfacility-type | Specifies the facility level used by the syslog messages; the default is local7. Possible values are local0, local1, local2, local3, local4, local5, local6, and local7. |
6 | Router(config)# End | Returns to privileged EXEC mode. |
7 | Router# show logging Hi guys, i'm making a texture pack that is for multiplayer (useless in singleplayer) that shows anyone invisible. I have edited the bubbles, arrows (so you can see if you shoot them with a bow) and a few other things (i forgot:P).It turns these things to bright red squares, so it is easy to spot them. Minecraft see invisible players texture pack. | Displays logging configuration. |
Step | Command | Purpose |
1 | Switch>(enable) set logging timestamp {enable | disable} | Configures the system to timestamp messages. |
2 | Switch>(enable) set logging serverip-address | Specifies the IP address of the syslog server; a maximum of three servers can be specified. |
3 | Switch>(enable) set logging server severityserver_severity_level | Limits messages that are logged to the syslog servers by severity level. |
4 | Switch>(enable) set logging server facilityserver_facility_parameter | Specifies the facility level that would be used in the message. The default is local7. Apart from the standard facility names listed in Table 4-1, Cisco Catalyst switches use facility names that are specific to the switch. The following facility levels generate syslog messages with fixed severity levels: 5: System, Dynamic-Trunking-Protocol, Port-Aggregation-Protocol, Management, Multilayer Switching 4: CDP, UDLD 2: Other facilities |
5 | Switch>(enable) set logging server enable | Enables the switch to send syslog messages to the syslog servers. |
6 | Digi tech 4 ld0266 4 manual. Switch>(enable) Show logging | Displays the logging configuration. |
Step | Command | Purpose |
1 | Pixfirewall# config terminal | Enters global configuration mode. |
2 | Pixfirewall(config)#logging timestamp | Specifies that each syslog message should have a timestamp value. |
3 | Pixfirewall(config)#logging host [interface connected to syslog server] ip_address [protocol/port] | Specifies a syslog server that is to receive the messages sent from the Cisco PIX Firewall. You can use multiple logging host commands to specify additional servers that would all receive the syslog messages. The protocol is UDP or TCP. However, a server can only be specified to receive either UDP or TCP, not both. A Cisco PIX Firewall only sends TCP syslog messages to the Cisco PIX Firewall syslog server. |
4 | Pixfirewall(config)#logging facilityfacility | Specifies the syslog facility number. Instead of specifying the name, the PIX uses a 2-digit number, as follows: local0 - 16 local1 - 17 local2 - 18 local3 - 19 local4 - 20 local5 - 21 local6 - 22 Ck2 a fallen man. local7 - 23 The default is 20. |
5 | pixfirewall(config)#logging traplevel | Specifies the syslog message level as a number or string. The level that you specify means that you want that level and those values less than that level. For example, if level is 3, syslog displays 0, 1, 2, and 3 messages. Possible number and string level values are as follows: 0: Emergency; System-unusable messages 1: Alert; Take immediate action 2: Critical; critical condition 3: Error; error message 4: Warning; warning message 5: Notice; normal but significant condition 6: Informational: information message 7: Debug; debug messages and log FTP commands and WWW URLs |
6 | pixfirewall(config)#logging on | Starts sending syslog messages to all output locations. |
7 | pixfirewall(config)#no logging message <message id> | Specifies a message to be suppressed. |
8 | pixfirewall(config)#exit | Exits global configuration mode. |